More than just a Source. A Solution. Made in USA with Pride Call Us Toll Free: 1.800.251.8351   I   Email
  • Bucket Hangers

    Truss To Truss Heavy Load Hangers
    Square-Skewed-Hip & Jack-Terminal Radial Member

    BH Bucket Hangers bolt to 2 x 8 min. webs.
    BHR Radial Hangers for multiple members.
    BHS Hangers are skewed 45°, specify right or left hand.
    BHJ Hangers carry 2 ply hip truss and end jack.
    BHT Terminal Hangers accept 45° hips, one or two ply, plus single ply end jack. Bolting plate is 1/4 x 7 x 27 high.

    Material : BH, BHS & BHJ all 1/4" A-36 steel. BHT pockets are 3/16" A-36 steel.
    Finish : Black copolymer finish.

    Caution - 2 x 8 maximum bottom chord on carrying girder. Skewed version requires special location of web.

    Warning - All girder plys must be securely fastened together to act as one unit and the hanger bolts are not to be considered for this purpose.

  • Girder Hangers

    Girder Hangers are medium duty hangers for girder-to-girder applications.
    Bolts are listed in fastener section of catalog.

    Material : Back plates are made of 3-gauge A-36 steel, stirrup seats are made of 7-gauge A-36 steel.
    Finish : Black copolymer paint.

  • Girder Truss Hangers

    Cleveland heavy-duty GT Hangers are the largest capacity nail-on hangers available. Select the part number that corresponds to your pocket needs and carrier chord conditions.

    Material : 3/16" A-36 steel.
    Finish : Black copolymer paint.

  • Hip & Jack Hangers - Heavy Duty

    Hip and jack pockets welded to carrier plates that mount to single, double or triple ply girders. Find the part number that matches the number of plys and depth of girder chord.

    Material : 3/16" A-36 steel.
    Finish : Black copolymer paint.

  • Heavy Duty Truss Hanger

    HJU Heavy Duty Facemount

    A facemount hanger that satisfies most truss to truss applications. Available for single, double and triple plys.

    Cautions : Always use a hanger that is the same depth as the girder chord. Do not use HJU 26 on 2 x 8 or 2 x 10.

    Material : 16 gauge or 14 gauge
    Finish : Galvanized G60.

  • Hip & Jack Hangers

    THJ Truss Hip & Jack Hanger

    The first hip and jack hanger that works right or left hand. Facemounts to 2 x 6 or 2 x 8 girder chord. Easy-nail flanges avoid the plated areas. Impressions in seat to align with panel point for perfect location, or hanger can be installed after corner truss is set. 3 1/4" seat bearing, tested and code approved.

    Material : 12 gauge
    Finish : Galvanized G60.

  • Hip & Jack & Hip Hangers

    A wider opening allows for a terminal condition with two hips and a jack.

    Reinforcement of the wider seat is provided by a stiffening flange at the rear of the seat.

    The THJH is available in heights to accommodate 2 x 6 and 2 x 8 girder truss bottom chords.

    Material : 12 gauge
    Finish : Galvanized G60.

  • Strap Hangers
  • Pocket Hanger

    Cleveland pocket hangers are made in standard and heavy gauges in popular sizes for residential and heavier construction. Designed for use with all floor joists and roof purlins as well as other framing applications.

    Immediately available from stock in all sizes listed in the table below. Packed in heavy corrugated containers for easy handling and convenient warehousing. Short, heavy nails designed for joist hangers are packed in each carton. Refer to tables for dimensions, nail sizes, packaging details and other information.

    Material : 18 gauge and 16 gauge.
    Finish : Galvanized G60.

  • Economy Pocket Hanger

    Low Cost Hangers for General Framing

    EPH Economy Pocket Hangers
    are engineered with less metal for lower cost, but full 1 1/2" seat bearing for allowable loads below. Speed prong aids installation.

    Material : 20 gauge
    Finish : Galvanized G60.

  • Recommended Facemount Hangers for Wood I-Beams

    There's a Cleveland Hanger to fit
    All Manufactured Wood I-Beams

    Facemount and Topmount
    hangers provide a low cost connection for the manufactured wood I-Beam industry.

    These hangers are intended for use with wood I-beams as made by various manufacturers.
    Hanger bearing is based on 565 psi for Southern Pine and nail value based on Douglas Fir-Larch and must be adjusted for other species of wood in accordance with U.B.C. Standard No. 25-17.

  • Facemount Hangers

    JUX Hangers are recommended for facemounting to LVL or PSL headers.

    Material : 16 gauge and 12 gauge.
    Finish : Galvanized G60.
    These hangers are intended for use with parallel strand lumber (PSL) or laminated veneer lumber (LVL).

  • Deep Seat

    Deep Seat

    (46)

    Hangers for Micro = Lam®, Parallam®, Gang-Lam®

    DS Deep Seat Hangers carry heavy loads obtained with Micro=Lam, Parallam and Gang-Lam products. Top flanges are 3-3/8" long with 2 nail holes per flange spaced for 3 1/2" minimum header, except DS 2.69 hangers have 2 1/2" top flanges.

    Load charts are based on seat compression of 600 psi. Solid header required. Consult your wood product manufacturer for limitations when LVL headers have top edge nailing.

    The 1 5/8" and 3 1/8" sizes are for 1 ply and 2 ply nominal lumber respectively. Other sizes are for LVL and PSL lumber.

    Material : 12 gauge.
    Finish : Galvanized G60.

  • Facemount Glulam Hangers

    Cleveland JU Glulam Hangers are made to order for sizes as shown. Also available for any size sawn timber, laminated beam or special beam in any design load. Prompt shipment.

    Material : 11 gauge and 7 gauge.
    Finish : Black copolymer paint, Hot-dip galvanized or stainless steel.

    Bulk packed in cartons.
    N4 Nails are 40d x 2-1/2" ring shank.
    Larger and special sizes available.

  • Topmount Glulam Hangers

    Cleveland JE Glulam Hangers are made to order for sizes as shown. Also available for 6 3/4 and 8 3/4 wide laminated timbers. Prompt shipment.

    Material : 11 gauge and 7 gauge.
    Finish : Black copolymer paint, Hot-dip galvanized or stainless steel.

    Bulk packed in cartons.
    Larger and special sizes available.

  • Welded Glulam Saddle Hangers


    Welded Hangers for Special ApplicationsW Style Hangers are made to order for your load and application.
    Cleveland designs special hangers to UBC requirements. When ordering advise load, uplift and header conditions.

    Glulam compression perpendicular to grain is 465 lbs. S.Y.P.

    Material : ASTM A-36 11 gauge, 3/16 and 1/4 gauge.
    Finish : Black copolymer paint, Hot-dip galvanized or stainless steel.
    Welded Hangers for Special Applications

  • Welded Solid-Sawn Hangers

    A wide range of sizes for solid-sawn nominal members is included. Full (rough) sizes are available; preceed part no. with (RS) for ordering. Allowable loads are based on group II species (SYP, DFL).

    Material : 11 gauge.
    Finish : Black Copolymer Paint, Hot-Dip Galvanized or Stainless Steel.

  • Welded Masonry

    Welded Masonry Hangers are placed in block under construction, eliminating the need for beam pockets. Anchorage is made by inserting two 16d duplex nails through the tabs into the cavity and grout.

  • TM Hangers
  • Skewed Hangers

    SK Hangers are skewed right (SKR) and left (SKL) in standard skews of 22 1/2 deg., 30 deg. 45 deg., 60 deg., and 67 1/2 deg. Excellent for hip roof framing of jacks and hip jack trusses. Full seat, slotted acute angle nailing.

    Material : 16 gauge.
    Finish : Galvanized G60.

  • JUO 26

    JU Hangers are a versatile, facemount style. They can be skewed up to 50°. Pitched seats - up or down - have neat corner welds. Welded seat hangers are made from 3/16" steel for loads greater than 2000 lbs.

    JUS Skewed hangers are made with the pocket either angled toward the right or the left. This allows for angled members to be supported.

    JUP Pitched hangers are made with the seat either sloped up or down.

    JUSP Skewed and Pitched hangers incorporate both the skewed and pitched characteristics.

    JUO Offset hangers are made with either the right or left flange formed inward. This style attaches at the end of a header or in tight areas.

    JUR Reverse hangers conceal the flanges or permit attachment at either end of the header. They are made for 3" and wider.

  • Severe Skew

    SKW style are face mount. Charted sizes are for single ply pockets. Other pocket widths available with same allowable loads. Heavy 11 gauge or 3/16" steel, black copolymer paint finish.

    SKWE style with top flange bearing.

    Material : 11 gauge and 7 gauge.
    Finish : Black copolymer paint.

  • Glulam Hinge Strap

    Glulam Hinge Connectors
    provide a high capacity connection between the cantilevered member and the supported member in positive vs negative moment situations. Members must be of equal width. Special configurations can be furnished to your specifications.

    Material : ASTM A-36 3/4", 1", and 1 1/4".
    Finish : Black copolymer paint, Hot-dip galvanized.

  • Glulam Hinge Strap

    GHS provide additional lateral load capacity when used with GHC connectors. The offset center section provides clearance for hinge connectors.

    GHS Straps are installed in pairs in conjunction with glulam hinge connectors. Seismic load duration of load increases of 33% and 60% are listed; no additional increases are permitted.

    Material : 7 gauge.
    Finish : Black copolymer paint, Hot-dip galvanized.

  • Beam Seats

    Beam Seats

    (28)

    Beam Seats anchor glulam beams to concrete and masonry supports. Seismic and wind resistance is provided. Special types are available.

    Material : 3 ga., 5/16" and 3/8".
    Finish : Black copolymer paint, Hot-dip galvanized or stainless steel.
    Duration of load increases of 33% and 60% are listed. Further increases are not allowed. Allowable loads for concrete, masonry, and wood to be verified by design engineer.

  • AFN Panel Hangers

    AFN series panel hangers are used in panelized wood roof systems to connect the 2 x 4 or 2 x 6 stiffeners to the purlins. The precision formed grippers on each side of the panel hanger are pressed into the wood providing a high-strength connection without the use of nails.
    Code Acceptance : ICBO accepted

    Material : 18 gauge.
    Finish : Galvanized.